About
Community
Bad Ideas
Drugs
Ego
Erotica
Fringe
Society
Technology
register | bbs | search | rss | faq | about
meet up | add to del.icio.us | digg it
Go Back   Community > Vices > Better Living Through Chemistry
FAQ Members List Calendar Search Today's Posts Mark Forums Read

Better Living Through Chemistry Discussions of any and all sorts of mind-warping chemicals, pills, booze, mind machines, trippy stuff, current street prices, importing pharmaceuticals, smart drugs, nutrients, herbs, and altered states. Please try to keep your conversations "theoretical" in nature, since this is an open conference.

Reply
 
Thread Tools Display Modes
 #1 
Old 2008-01-22, 00:50
mksnowboarder mksnowboarder is offline
Regular
 
Default Preparing Amphetamine Sulfate for Injection

Just out of curiosity, I was wondering if it was safe to inject amphetamine sulfate.

Being in the form of instant release adderall tablets, one has a large quantity of amphetamine sulfate. Injecting methamphetamine was acceptable compared to smoking, insufflation, or oral ingestion. Does this principle apply to the lesser form?

Would it be as simple as preparing say an oxy? Dissolve in spoon with water, heat, filter, and inject? Would that adequately remove fillers and binders? Any thoughts?

mike
 #2 
Old 2008-01-22, 00:58
bobert the man bobert the man is offline
Regular
 
Default Re: Preparing Amphetamine Sulfate for Injection

Now im no chemist or biologist, but i Know that those pills contain binders which are not in fact any good for you. Well really, they just might up and kill you.

Dont fuck around with a needle. Just smoke or snort the shit and try to keep your life on track before hell breaks loose, because whatever you tell yourself, it will happen eventually.
 #3 
Old 2008-01-22, 01:05
mksnowboarder mksnowboarder is offline
Regular
 
Default Re: Preparing Amphetamine Sulfate for Injection

All pills contain fillers and binders, fool. I mentioned that in my original post. See, most of these fillers and binders are not water soluble, whereas amphetamine is. When you filter the liquid through a cotton ball, only the products dissolved in the water end up in the syringe. Thus, unless the fillers and binders are in themselves water soluble, it does not present a problem.

Smoking it would be impossible due to the fillers and binders, and snorting it is not much more effective than oral ingestion.

I've done plenty of "fucking with the needle" in the past, and my life is just fine, thank you. I didn't need moral advice; I needed someone with a knowledge of chemistry to tell me if what I wanted to do was possible.

Next?

mike
 #4 
Old 2008-01-22, 01:15
FuckedintheHead FuckedintheHead is offline
Regular
 
Default Re: Preparing Amphetamine Sulfate for Injection

I would try my best to get ahold of a micron filter if I was you, just to be safe you know?

If you can't find one of those, then filter through a cotton, and then take that filtered solution and filter again. Sure, you may lose a little bit of your shit, but it is alot better than shooting up pill binders.

Make sure there is ZERO particulate matter floating around in your syring before bangin up. If there is, then filter it again.

Are you talking about those blue 10mg adderall tabs?

Oh yeah, I forgot. After you filter it make sure to filter it again ;).
 #5 
Old 2008-01-22, 01:24
Regular
 
Penn's Woods
Default Re: Preparing Amphetamine Sulfate for Injection

I watched my friend shoot adderall once. The solution was orange, and I forced him to run it through cotton 4-5 times before he shot just because it looked so terrible. I wouldn't do it IMO unless I had a micron filter. I think it was adderall
 
To the best of our knowledge, the text on this page may be freely reproduced and distributed.
 

totse.com certificate signatures
 
 
About | Community | Bad Ideas | Drugs | Ego | Erotica | Fringe | Society | Technology
Hot Topics